Section 8 — Heat Transfer Equipment

Air Cooled Heat Exchangers Data Sheet

IPE Engineering Practice IPE-EP-8-1-4DS

Document number: IPE-EP-8-1-4DS · Section: 8 — Heat Transfer Equipment

8. PERFORMANCE DATA - TUBE SIDE

10.

11.

12.

13.

14.

15.

16.

17.

18.

19. PERFORMANCE DATA - AIR SIDE

20.

21.

22.

23.

24. DESIGN - MATERIALS - CONSTRUCTION

25.

26.

27.

28.

29.

30.

31.

32.

33.

34.

35.

36.

37.

38.

* Give tube count of each pass when irregular

** Motors shall be in accordance with EP 13-3-1 and a completed Motor Data Sheet EP 13-3-1DS.

FAN, Mfr. & Model	FAN, Mfr. & Model	FAN, Mfr. & Model	DRIVER, Type**	DRIVER, Type**	DRIVER, Type**	SPEED REDUCER, Type	SPEED REDUCER, Type
No./Bay	RPM	RPM	Mfr.	Mfr.	Mfr.	Mfr. & Model	Mfr. & Model
Dia.	No. Blades	No. Blades	No. Bay	HP/driver	HP/driver	No. Bay	No. Bay
PitchAdj.Auto.	Angle	Angle	RPM AGMA Rating HP	RPM AGMA Rating HP	RPM AGMA Rating HP	RPM AGMA Rating HP	Rated 1
Material, Blade	Hub	Hub	Enclosure Support (Structural)	Enclosure Support (Structural)	Enclosure Support (Structural)	Enclosure Support (Structural)	Enclosure Support (Structural)
HP, Fan. Des.	Minimum Amb.	Minimum Amb.	Volt, Phase, Cycle	Volt, Phase, Cycle	Volt, Phase, Cycle	Volt, Phase, Cycle	Volt, Phase, Cycle
Control Action on Air Failure - Fan Pitch: (Minimum) (Maximum) (Lockup) Louver: (Open) (Close) (Lockup)	Control Action on Air Failure - Fan Pitch: (Minimum) (Maximum) (Lockup) Louver: (Open) (Close) (Lockup)	Control Action on Air Failure - Fan Pitch: (Minimum) (Maximum) (Lockup) Louver: (Open) (Close) (Lockup)	Control Action on Air Failure - Fan Pitch: (Minimum) (Maximum) (Lockup) Louver: (Open) (Close) (Lockup)	Control Action on Air Failure - Fan Pitch: (Minimum) (Maximum) (Lockup) Louver: (Open) (Close) (Lockup)	Control Action on Air Failure - Fan Pitch: (Minimum) (Maximum) (Lockup) Louver: (Open) (Close) (Lockup)	Control Action on Air Failure - Fan Pitch: (Minimum) (Maximum) (Lockup) Louver: (Open) (Close) (Lockup)	Control Action on Air Failure - Fan Pitch: (Minimum) (Maximum) (Lockup) Louver: (Open) (Close) (Lockup)
Degree Control of Outlet Process Temperature (Maximum Cooling) ( F)	Degree Control of Outlet Process Temperature (Maximum Cooling) ( F)	Degree Control of Outlet Process Temperature (Maximum Cooling) ( F)	Degree Control of Outlet Process Temperature (Maximum Cooling) ( F)	Degree Control of Outlet Process Temperature (Maximum Cooling) ( F)	Degree Control of Outlet Process Temperature (Maximum Cooling) ( F)	Degree Control of Outlet Process Temperature (Maximum Cooling) ( F)	Degree Control of Outlet Process Temperature (Maximum Cooling) ( F)
Recirculation (None) (Internal) (External Over Side) (External Over End) Steam Coil (Yes)	Recirculation (None) (Internal) (External Over Side) (External Over End) Steam Coil (Yes)	Recirculation (None) (Internal) (External Over Side) (External Over End) Steam Coil (Yes)	Recirculation (None) (Internal) (External Over Side) (External Over End) Steam Coil (Yes)	Recirculation (None) (Internal) (External Over Side) (External Over End) Steam Coil (Yes)	Recirculation (None) (Internal) (External Over Side) (External Over End) Steam Coil (Yes)	Recirculation (None) (Internal) (External Over Side) (External Over End) Steam Coil (Yes)	(No)
NOTES: * Give tube count of each pass when irregular	NOTES: * Give tube count of each pass when irregular	NOTES: * Give tube count of each pass when irregular	NOTES: * Give tube count of each pass when irregular	NOTES: * Give tube count of each pass when irregular	NOTES: * Give tube count of each pass when irregular	NOTES: * Give tube count of each pass when irregular	NOTES: * Give tube count of each pass when irregular
** Motors shall be in accordance with EP 13-3-1 and a completed Motor Data Sheet from EP 13-3-1DS.	** Motors shall be in accordance with EP 13-3-1 and a completed Motor Data Sheet from EP 13-3-1DS.	** Motors shall be in accordance with EP 13-3-1 and a completed Motor Data Sheet from EP 13-3-1DS.	** Motors shall be in accordance with EP 13-3-1 and a completed Motor Data Sheet from EP 13-3-1DS.	** Motors shall be in accordance with EP 13-3-1 and a completed Motor Data Sheet from EP 13-3-1DS.	** Motors shall be in accordance with EP 13-3-1 and a completed Motor Data Sheet from EP 13-3-1DS.	** Motors shall be in accordance with EP 13-3-1 and a completed Motor Data Sheet from EP 13-3-1DS.	** Motors shall be in accordance with EP 13-3-1 and a completed Motor Data Sheet from EP 13-3-1DS.

MISCELLANEOUS DATA	MISCELLANEOUS DATA	MISCELLANEOUS DATA	MISCELLANEOUS DATA	MISCELLANEOUS DATA	MISCELLANEOUS DATA	MISCELLANEOUS DATA	MISCELLANEOUS DATA
Plot Area ft2	Plot Area ft2	Weight of Bundle lb.	Weight of Bundle lb.	Weight of Bundle lb.	Shipping Weight	Shipping Weight	lb.
REMARKS:	REMARKS:	REMARKS:	REMARKS:	REMARKS:	REMARKS:	REMARKS:	REMARKS:

© 2026 Inflection Point Engineering, LLC. All rights reserved. The content of this page — including calculation methods, reference data, written analysis, interactive tools, and source code — is the intellectual property of Inflection Point Engineering, LLC and is protected under applicable copyright, trademark, and trade secret laws. Unauthorized reproduction, redistribution, modification, or derivative use in whole or in part is prohibited without prior written consent.

Disclaimer. This material is provided for informational and educational purposes only and does not constitute professional engineering advice. Calculations, reference data, and methodologies are based on published standards and accepted engineering practice but are not a substitute for engineering judgment, site-specific analysis, or review by a licensed Professional Engineer. Inflection Point Engineering, LLC makes no warranties, express or implied, regarding the accuracy, completeness, or fitness for a particular purpose of any content presented here, and shall not be liable for any direct, indirect, incidental, or consequential damages arising from its use. Users assume all risk associated with applying this content to real-world design, operations, or decisions.