IPE-EP-5-3-8DS

IPE Engineering Practice IPE-EP-5-3-8DS

Document number: IPE-EP-5-3-8DS · Section: 5 — Piping

CoInafsletcatilo nA Prouinbta E nEgningeeirninege Prriancgtic Pesractices Check Valves Data Sheet PROJECT PROJECT NO. INQUIRY NO. LOCATION UNIT EQUIPMENT ID JOB NO. DOCUMENT NO. DATA ISSUED FOR IN-HOUSE REVIEW COASTAL ARUBA APPROVAL QUOTATION PURCHASE CONSTRUCTION THIS SHEET IS A RECORD OF EACH ISSUE OR REVISION TO THE SUBJECT DATA. EACH TIME THE DATA ALL DATA SHEETS ATTACHED IS CHANGED ONLY THE NEW OR REVISED DATA SHEETS NEED TO BE ISSUED. THE EXACT SHEETS CHANGED AND THE NATURE OF THE CHANGE SHOULD BE NOTED UNDER REMARKS. THESE REMARKS ARE NOT A PART OF THE DATA. THE REVISED DATA SHEET(S) BE COME PART OF THE ORIGINAL DATA AND SHALL BE COMPLIED WITH IN THEIR ENTIRETY. REVISED DATA SHEET(S) ONLY ATTACHED REV. DATE BY CHECK APPROVALS REMARKS SECTION PROJECT Coastal Aruba

CoInafsletcatilo nA Prouinbta E nEgningeeirninege Prriancgtic Pesractices Check Valves Data Sheet EQUIPMENT ID JOB NO. DOCUMENT NO REV. *1. VALVE TAG IDENTIFICATION: *2. VALVE SIZE: *3. CLASS: *4. DESIGN TEMPERATURE: *5. BODY TYPE: *6. VALVE END CONNECTION TYPE: *7. INTEGRAL OR WELDED FLANGE: *8. VALVE TYPE: *9. MATING FLANGE STANDARD: *10. WAFER OR FLANGE FACING: *11. DRAIN CONNECTIONS: *12. BODY SEATS: 13. LIFTING EYEBOLTS: *14. BOLT HOLES: *15. BYPASS REQUIREMENT WAFER PLATE TYPE: *16. VALVE SHELL MATERIAL: 17. BONNET GASKET AND FLANGE FACING: 18. COVER BOLT MATERIAL: 19. FLAPPER PLATE SIZE: *20. API TRIM NUMBER: 21. INSPECTION AND TESTING REQUIREMENT: 22. ALTERNATIVE COLOR: 23. PACKAGING: 24. NOTES:

*1. VALVE TAG IDENTIFICATION:
*2. VALVE SIZE:
*3. CLASS:
*4. DESIGN TEMPERATURE:
*5. BODY TYPE:
*6. VALVE END CONNECTION TYPE:
*7. INTEGRAL OR WELDED FLANGE:
*8. VALVE TYPE:
*9. MATING FLANGE STANDARD:
*10. WAFER OR FLANGE FACING:
*11. DRAIN CONNECTIONS:
*12. BODY SEATS:
13. LIFTING EYEBOLTS:
*14. BOLT HOLES:
*15. BYPASS REQUIREMENT WAFER PLATE TYPE:
*16. VALVE SHELL MATERIAL:
17. BONNET GASKET AND FLANGE FACING:
18. COVER BOLT MATERIAL:
19. FLAPPER PLATE SIZE:
*20. API TRIM NUMBER:
21. INSPECTION AND TESTING REQUIREMENT:
22. ALTERNATIVE COLOR:
23. PACKAGING:
24. NOTES:

© 2026 Inflection Point Engineering, LLC. All rights reserved. The content of this page — including calculation methods, reference data, written analysis, interactive tools, and source code — is the intellectual property of Inflection Point Engineering, LLC and is protected under applicable copyright, trademark, and trade secret laws. Unauthorized reproduction, redistribution, modification, or derivative use in whole or in part is prohibited without prior written consent.

Disclaimer. This material is provided for informational and educational purposes only and does not constitute professional engineering advice. Calculations, reference data, and methodologies are based on published standards and accepted engineering practice but are not a substitute for engineering judgment, site-specific analysis, or review by a licensed Professional Engineer. Inflection Point Engineering, LLC makes no warranties, express or implied, regarding the accuracy, completeness, or fitness for a particular purpose of any content presented here, and shall not be liable for any direct, indirect, incidental, or consequential damages arising from its use. Users assume all risk associated with applying this content to real-world design, operations, or decisions.