General Requirements for Buildings Inspection Checklist

IPE Engineering Practice IPE-EP-4-6-1C

Document number: IPE-EP-4-6-1C · Section: 4 — Structures and Foundations

THE MANUFACTURER OF EQUIPMENT PURCHASED BY REFINING COMPANY SHALL BE RESPONSIBLE FOR MEETING ALL APPLICABLE REQUIREMENTS OF THE ENGINEERING PRACTICES AND OTHER DOCUMENTS REFERENCED THEREIN REGARDLESS OF WHETHER THE ITEMS ARE INSPECTED BY A REPRESENTATIVE.

REFERENCES

THE LATEST EDITION OF THE FOLLOWING STANDARDS AND PUBLICATIONS ARE REFERRED TO HEREIN.

ENGINEERING PRACTICES

EP 4-5-2 IC STRUCTURAL STEEL CONSTRUCTION INSPECTION CHECKLIST EP 4-3-2 IC CONCRETE CONSTRUCTION INSPECTION CHECKLIST

EP 4-6-1 GENERAL REQUIREMENTS FOR BUILDINGS

FREQUENCY OF CONTACT BY THE INSPECTOR: (CHECK ONE)

LEVEL 1: ON CALL BY FABRICATOR LEVEL 2: ONCE EVERY TWO WEEKS LEVEL 3: EVERY WEEK

LEVEL 4: DAILY

LEVEL 5: RESIDENT

LEVEL 6: OTHER, SPECIFY

LEVEL OF INSPECTION BY THE INSPECTOR: (CHECK ONE)

LEVEL 1: PREFABRICATION MEETING, DOCUMENT REVIEW, AND FINAL INSPECTION

LEVEL 2: PREFABRICATION MEETING, DOCUMENT REVIEW, REVIEW ITEMS, AND FINAL INSPECTION LEVEL 3: PREFABRICATION MEETING, DOCUMENT REVIEW, REVIEW ITEMS, WITNESS POINTS, AND FINAL

INSPECTION

LEVEL 4: PREFABRICATION MEETING, DOCUMENT REVIEW, REVIEW ITEMS, WITNESS POINTS, HOLD POINTS, AND FINAL INSPECTION

LEVEL 5: OTHER, SPECIFY

EQUIPMENT ID	JOB NO.	DOCUMENT NO.	REV.

R CHECK: THE SHOP INSPECTOR SHALL REVIEW DOCUMENTED RESULTS OF INSPECTION PERFORMED BY VENDOR'S INSPECTION OR SUBCONTRACTED INSPECTOR.

W CHECK: INDICATES THE SHOP INSPECTOR SHALL WITNESS ITEM DURING FABRICATION. SHOP SHALL NOTIFY INSPECTOR TWO DAYS IN ADVANCE OF FABRICATION POINT BUT NEED NOT HOLD PRODUCTION FOR INSPECTION.

H CHECK: INDICATES THE SHOP INSPECTOR SHALL INSPECT ITEM DURING HOLD ON FABRICATION. SHOP SHALL NOTIFY INSPECTOR FIVE DAYS IN ADVANCE OF FABRICATION POINT AND SHALL NOT CONTINUE AFFECTED PRODUCTION UNTIL INSPECTOR PERFORMS INDICATED INSPECTION.

R	W	H	INSPECTION/TESTING ACTIVITY	INSPECTOR'S INITIALS (REVIEW COMPLETE)	DATE
			MATERIALS ARE AS PRESCRIBED IN EP 4-6-1: 5.0
			DOORS COMPLY WITH EP 4-6-1: 6.2
			WINDOWS COMPLY WITH EP 4-6-1: 6.3
			FLOORS PROVIDED WITH VAPOR BARRIER (EP 4-6-1: 6.4)
			FIRE PROTECTION SYSTEM PER EP 4-6-1: 6.5
			PLUMBING FACILITIES PER DRAWINGS AND EP 4-6-1: 7.0
			SANITARY FACILITIES PER EP 4-6-1: 7.0
			VENTILATION SYSTEMS DESIGNED AND INSTALLED PER EP 4-6-1: 8.2
			AIR CONDITIONING DESIGNED AND INSTALLED PER EP 4-6- 1: 8.3
			DRAWINGS AND SPECIFICATIONS COMPLY WITH EP 4-6-1: 9.0
			FOUNDATION INSPECTION PER EP 4-3-2C AND EP 4-6-1: 10.1
			CONCRETE SLAB INSPECTION (EP 4-6-1: 10.1)
			FRAME INSPECTION EP 4-6-1: 10.1, EP 4-3-2C, EP 4-5-2C
			PRE-PLASTERING INSPECTION (EP 4-6-1: 10.1)
			FINAL INSPECTION BEFORE OCCUPANCY(EP 4-6-1: 10.1)
			ADDITIONAL REQUIREMENTS APPROPRIATE TO BUILDING- TYPE SATISFIED (EP 4-6-1: 11.0)

INSPECTOR SIGN-OFF	INSPECTOR SIGN-OFF	INSPECTOR SIGN-OFF	INSPECTOR SIGN-OFF
INITIALS	NAME	COMPANY	SOCIAL SECURITY NUMBER

EQUIPMENT ID	JOB NO.	DOCUMENT NO.	REV.

SUMMARY:

© 2026 Inflection Point Engineering, LLC. All rights reserved. The content of this page — including calculation methods, reference data, written analysis, interactive tools, and source code — is the intellectual property of Inflection Point Engineering, LLC and is protected under applicable copyright, trademark, and trade secret laws. Unauthorized reproduction, redistribution, modification, or derivative use in whole or in part is prohibited without prior written consent.

Disclaimer. This material is provided for informational and educational purposes only and does not constitute professional engineering advice. Calculations, reference data, and methodologies are based on published standards and accepted engineering practice but are not a substitute for engineering judgment, site-specific analysis, or review by a licensed Professional Engineer. Inflection Point Engineering, LLC makes no warranties, express or implied, regarding the accuracy, completeness, or fitness for a particular purpose of any content presented here, and shall not be liable for any direct, indirect, incidental, or consequential damages arising from its use. Users assume all risk associated with applying this content to real-world design, operations, or decisions.