Grouting and Baseplate for Structural Steel Equipment Installation Inspection Checklist

IPE Engineering Practice IPE-EP-4-2-9C

Document number: IPE-EP-4-2-9C · Section: 4 — Structures and Foundations

EQUIPMENT ID	JOB NO.	DOCUMENT NO.	REV.

THE MANUFACTURER OF EQUIPMENT PURCHASED BY INFLECTION POINT ENGINEERING, LLC SHALL BE RESPONSIBLE FOR MEETING ALL APPLICABLE REQUIREMENTS OF THE IPE ENGINEERING PRACTICES AND OTHER DOCUMENTS REFERENCED THEREIN REGARDLESS OF WHETHER THE ITEMS ARE INSPECTED BY A IPE REPRESENTATIVE.

REFERENCES

THE LATEST EDITION OF THE FOLLOWING STANDARDS AND PUBLICATIONS ARE REFERRED TO HEREIN.

IPE ENGINEERING PRACTICES

EP 4-2-9 GROUTING AND BASEPLATES FOR STRUCTURAL STEEL AND EQUIPMENT EP 6-8-1 STORAGE AND INSTALLATION OF ROTATING EQUIPMENT

FREQUENCY OF CONTACT BY THE INSPECTOR: (CHECK ONE)

LEVEL 1: ON CALL BY FABRICATOR LEVEL 2: ONCE EVERY TWO WEEKS LEVEL 3: EVERY WEEK

LEVEL 4: DAILY

LEVEL 5: RESIDENT

LEVEL 6: OTHER, SPECIFY ______________

LEVEL OF INSPECTION BY THE INSPECTOR: (CHECK ONE)

LEVEL 1: PREFABRICATION MEETING, DOCUMENT REVIEW, AND FINAL INSPECTION

LEVEL 2: PREFABRICATION MEETING, DOCUMENT REVIEW, REVIEW ITEMS, AND FINAL INSPECTION LEVEL 3: PREFABRICATION MEETING, DOCUMENT REVIEW, REVIEW ITEMS, WITNESS POINTS, AND FINAL

INSPECTION

LEVEL 4: PREFABRICATION MEETING, DOCUMENT REVIEW, REVIEW ITEMS, WITNESS POINTS, HOLD POINTS, AND FINAL INSPECTION

LEVEL 5: OTHER, SPECIFY ______________

EQUIPMENT ID	JOB NO.	DOCUMENT NO.	REV.

R CHECK: THE SHOP INSPECTOR SHALL REVIEW DOCUMENTED RESULTS OF INSPECTION PERFORMED BY VENDOR'S INSPECTION OR SUBCONTRACTED INSPECTOR.

W CHECK: INDICATES THE SHOP INSPECTOR SHALL WITNESS ITEM DURING FABRICATION. SHOP SHALL NOTIFY INSPECTOR TWO DAYS IN ADVANCE OF FABRICATION POINT BUT NEED NOT HOLD PRODUCTION FOR INSPECTION.

H CHECK: INDICATES THE SHOP INSPECTOR SHALL INSPECT ITEM DURING HOLD ON FABRICATION. SHOP SHALL NOTIFY INSPECTOR FIVE DAYS IN ADVANCE OF FABRICATION POINT AND SHALL NOT CONTINUE AFFECTED PRODUCTION UNTIL INSPECTOR PERFORMS INDICATED INSPECTION.

R	W	H	INSPECTION/TESTING ACTIVITY	INSPECTOR'S INITIALS (REVIEW COMPLETE)	DATE
			GROUTING SPECIFICATIONS HAVE BEEN APPROVED BY THE OWNER'S ENGINEER (EP 4-2-9: 6.1)
			GROUTING SPECIFICATION INCLUDES SPECIFIC REQUIREMENTS OF VENDOR OR MACHINE MANUFACTURER (EP 4-2-9: 6.1)
			NONBONDING SURFACES HAVE BEEN COATED (EP 4-2-9: 6.2)
			METAL SURFACES HAVE BEEN PREPARED (EP 4-2-9: 6.2)
			CONCRETE SURFACES HAVE BEEN PREPARED (EP 4-2-9: 6.2)
			FORMS ARE PREPARED (EP 4-2-9: 6.3)
			GROUT HAS BEEN PROPERLY MIXED (EP 4-2-9: 6.3, 6.4)
			GROUT IS PLACED PROPERLY (EP 4-2-9: 6.5)
			GROUT HAS BEEN CURED AND FINISHED PER EP 6-5-2: 6.6
			VOID CHECK HAVE BEEN PERFORMED (EP 4-2-9: 6.7)
			REPAIRS, IF NEEDED, HAVE BEEN MADE PER EP 4-2-9:6.7
			FINAL GROUT SURFACES HAVE BEEN PROTECTED PER EP 4-2-9: 6.8
			GROUT SPECIMEN HAVE BEEN PROPERLY TESTED (EP 4- 2-9: 6.9)
			BASEPLATES HAVE BEEN INSTALLED PER EP 4-2-9: 7.3
			ADDITIONAL REQUIREMENTS OF MACHINERY INSTALLATION PRACTICE HAVE BEEN MET (EP 6-8-1)

EP 4-2-9 C CONCRETE INSPECTION DAILY LOG SHEET

AS A MINIMUM, THE FOLLOWING LEVELS OF INSPECTION SHALL BE PERFORMED:

P CHECK: CHECK PRIOR TO STARTING WORK ON EACH SHIFT

R CHECK: IN ADDITION TO "P" CHECK, MAKE RANDOM CHECKS DURING SHIFT

		READINGS	READINGS
		TIME	VALUE
P	SURFACE CONDITIONS (6.2)



P	FORM CONDITIONS (6.3)



R	GROUT MIXED PROPERLY (6.4)



R	PLACEMENT REQUIREMENTS MET (6.5)



P	CURE CONDITIONS (6.6)

INSPECTOR SIGN-OFF	INSPECTOR SIGN-OFF	INSPECTOR SIGN-OFF	INSPECTOR SIGN-OFF
INITIALS	NAME	COMPANY	SOCIAL SECURITY NUMBER

SUMMARY:

© 2026 Inflection Point Engineering, LLC. All rights reserved. The content of this page — including calculation methods, reference data, written analysis, interactive tools, and source code — is the intellectual property of Inflection Point Engineering, LLC and is protected under applicable copyright, trademark, and trade secret laws. Unauthorized reproduction, redistribution, modification, or derivative use in whole or in part is prohibited without prior written consent.

Disclaimer. This material is provided for informational and educational purposes only and does not constitute professional engineering advice. Calculations, reference data, and methodologies are based on published standards and accepted engineering practice but are not a substitute for engineering judgment, site-specific analysis, or review by a licensed Professional Engineer. Inflection Point Engineering, LLC makes no warranties, express or implied, regarding the accuracy, completeness, or fitness for a particular purpose of any content presented here, and shall not be liable for any direct, indirect, incidental, or consequential damages arising from its use. Users assume all risk associated with applying this content to real-world design, operations, or decisions.